Digital Electronics Quiz Vol- 2(Advance Level)

This is the Digital electronics quiz vol- 2 which is more advanced than Digital Electronics Quiz-1. This is a bit more advanced version of it. Enjoy the Quiz game there will be 50 questions.

Please enter your email:

1. Which type of device FPGA are?

SLD

PLD

SROM

EEPROM

2. In FPGA, vertical and horizontal directions are separated by __________

A line

A strobe

A channel

A flip-flop

3. A D flip-flop utilizing a PGT clock is in the CLEAR state. Which of the following input actions will cause it to change states?

CLK = NGT, D = 0

CLK = PGT, D = 0

CLOCK NGT, D =1

CLOCK PGT, D =1

4. Why do the D flip-flops are said to be as Data Flip-flops’?

Due to its capability to receive data from flip-flop

Due to its capability to store data in flip-flop

Due to its capability to transfer the data into flip-flop

Due to erasing the data from the flip-flop

5. The D flip-flop has _______ input.

6. An S-R Flip-Flop has 2 inputs marked ______& ______ and two outputs __&__.

Stable&Reset, Q & Q’

Select&Reset, Q’ & Q’

Set & Reset, Q& Q’

System&Reset, Q & Q’

7. Define trigger pulse?

A pulse that reverses the cycle of operation

A pulse that starts a cycle of operation

A pulse that prevents a cycle of operation

A pulse that enhances a cycle of operation

8. JK flip flop has _____

No memory

Temporary memory

True Memory

Random

9. Schmitt trigger can be used as

Squarewave generator

Comparator

Both A and B

None of the above

10. In D flip-flop, if clock input is LOW, the D input ______

Has no effect

Goes high

Goes low

keeps deflecting

11. In an S-R Flip-Flop, Q output is set to logic 1 by applying logic 0 to the _____.

S input

R input

Toggle input

CLK input

12. The output of Up counters goes on increasing due to _____

Transmission of clock pulses

Reception of clock pulses

Both a and b

None of the above.

13. A shift register is defined as ______

The register capable of shifting information either to the right or to the left

The register capable of shifting information to another register

The register capable of shifting information to the right only

The register capable of shifting information to the left only

14. On a master-slave flip-flop, when is the master enabled?

when the gate is LOW

when the gate is HIGH

Can be either and or

None of the above

15. If the number of states in a counter are 2ⁿ, then the value of ‘n’ is ______

Less than the number of flip flops

Greater than the number of flip flops

Equal to the number of flip flops

Unpredictable

16. Three decade counter would have _______

2 BCD counters

3 BCD counters

4 BCD counters

5 BCD counters

17. UP-DOWN counter is a combination of _______

Latches

Flip-flops

UP counter

Up counter & down counter

18. A PLA is similar to a ROM in concept except that ______

It hasn’t capability to read only

It hasn’t capability to read or write operation

It hasn’t capability to write only

t doesn’t provide full decoding to the variables

19. How is a J-K flip-flop made to toggle?

J = 0, K = 0

J = 0, K = 1

J = 1, K = 0

J = 1, K = 1

20. What amongst the following is faster in operation?

Sequential Circuits

Latches

Flip-flops

Combinational Circuits

21. Why is the extent of propagation delay in synchronous counter much lesser than that of the asynchronous counter?

Due to the clocking of all flip flops at the same instant

Due to the increase in the number of states

Due to absence of mode control operation

Due to the absence of connection between the output of the preceding flip flop and the clock of the next one

22. How many types of registers available?

23. Total number of inputs in a half adder is _____

24. How many AND, OR and EXOR gates are required for the configuration of full adder?

1, 2, 2

2, 1, 2

3, 1, 2

4, 0, 1

25. Which sequential circuits are used for counting pulses?

Counters

Registers

Latches

Flip-Flops

26. Set pin going high in SR flip flop causes the output to go to

Invalid

Default

27. The inputs in the PLD is given through _______

NAND

NOR

AND

28. The SR flip-flop can be considered as a ___ memory

2-Bit

1-bit

8-Bit

4-Bit

29. In DOWN-counter, each flip-flop is triggered by _______

The output of the next flip-flop

The normal output of the preceding flip-flop

The clock pulse of the previous flip-flop

The inverted output of the preceding flip-flop

30. A register that is used to store binary information is called a ________.

Binary Register

Data Register

Shift Register

Counter

31. In which operation carry is obtained?

Addition

Subtraction

Multiplication

Both addition and subtraction

32. If A, B, and C are the inputs of a full adder then the sum is given by ______

A AND B AND C

A OR B AND C

A XOR B XOR C

A OR B OR C

33. In an UP-counter, each flip-flop is triggered by _______

The output of the next flip-flop

The normal output of the preceding flip-flop

The inverted output of the preceding flip-flop

The clock pulse of the previous flip-flop

34. D flip-flop can be made from a J-K flip flop by making

J=K

J=K=1

J=Q, K=1

35. _____ input in an S-R Flip-Flop resets the flip-flop to its original value with an output Q, that will be at Logic ‘0’ or ‘1’ depending upon the set/reset condition.

Reset

Set

Clock

Q’

36. In D flip-flop, if clock input is HIGH & D=1, then output is ______[quads id=1]

Hint

Toggle

Invaid

37. A counter circuit is usually made up of _____

A number of latches connected in cascade form

A number of NAND gates connected in cascade form

A number of NOR gates connected in cascade form

A number of flip-flops connected in cascade

38. The main difference between a register and a counter is ______

A counter has no specific sequence of states

A register has no specific sequence of states

A register has the capability to store one bit of information but the counter has n-bit

A register counts data

39. The register is a type of ________

Combinational Circuit

Sequential Circuit

Latch

Counter

40. The process to activate a Flip-Flop is______

Negative edge trigger

Positive edge trigger

Either positive or Negative edge trigger

Sinusoidal trigger

41. In serial shifting method, data shifting occurs ______

One bit at a time

simultaneously

Four bit at a time

Two bit at a time

42. In SR flip-flop, ‘S’ stands for:

Stable

Selective

Set

Systematic

43. A modulus-10 counter must have _____

10 flip-flops

4 Flip-flops

2 flip-flops

Synchronous clocking

44. A register can be defined as ______

The group of latches for storing one bit of information.

The group of latches for storing n-bit of information.

The group of flip-flops suitable for storing one bit of information.

The group of flip-flops suitable for storing binary information

45. _____ input in an S-R Flip-Flop resets the flip-flop to its original value with an output Q, that will be at Logic ‘0’ or ‘1’ depending upon the set/reset condition.

Reset

Set

Clock

Q’

46. A feature that distinguishes the J-K flip-flop from the D flip-flop is the

toggle condition

preset input

clear input

type of clock

47. lf, A and B are the inputs of a half adder, the carry is given by

A AND B

A OR B